Markers and phase changes
The mesh moves with the material, but it is rebuilt when it distorts, and an element then no longer holds one rock. DES therefore tracks material identity with markers: points that move with the deformation, each carrying a material index. An element's properties are the marker-weighted means described in Rheology.
Markers
Each marker stores the element that contains it and its barycentric coordinates there, so it moves exactly with the element and needs no search while the mesh only deforms. After remeshing, every marker is located in the new mesh.
Initial markers. markers.init_marker_option = 1 scatters
markers.markers_per_element markers randomly in each element (seeded by
markers.random_seed); 2 places them on a regular grid with spacing
markers.init_marker_spacing, in units of mesh.resolution. Their
material comes from ic.mattype_option: 0 takes the region of a
.poly mesh, 1 assigns horizontal layers at ic.mattype_layer_depths
(in units of mesh.zlength), and 101 calls a custom routine in the
source.
Replenishment. Remeshing and stretching can leave an element with few
markers. When it holds fewer than markers.min_num_markers_in_element, a
marker is added. Its material follows markers.replenishment_option: 0
material 0, 1 drawn from the materials of the element and its neighbours
in proportion, 2 the material of the nearest marker; the
parameter reference lists the other options.
Phase changes
A phase change converts a marker from one material to another when its
pressure and temperature cross a reaction boundary; the element properties
then follow the new marker counts. mat.phase_change_option selects the
rules:
| Option | Rules |
|---|---|
| 0 | none (default) |
| 1 | a fixed set of subduction rules on fixed material indices 0–7 |
| 3 | the subduction rule engine: rules switched on one by one, materials named by parameters |
| 101 | a custom routine in phasechanges.cxx |
Phase changes need at least two materials.
Option 3: the subduction rule engine
Each rule converts the material named by one mat.mattype_* parameter into
another when its predicate holds. Depth is measured below the current
local free surface; temperature is in °C below. The pressure
(compression positive) is the mean stress of the marker's element with
mat.phase_change_pressure_option = 0, so tectonic over- and
underpressure move the boundaries, or the lithostatic reference pressure at
that depth with 1.
| Switch | Conversion | Boundary |
|---|---|---|
mat.has_eclogitization (on) | oceanic crust → eclogite | , km, GPa and GPa (Hacker et al., 2003) |
mat.has_serpentinization (on) | mantle above wet slab crust → serpentinite | inside the antigorite stability field (Ulmer & Trommsdorff, 1995) and within mat.serpentinization_thickness above oceanic crust or sediment, no deeper than mat.serpentinization_max_depth |
mat.has_serpentinization (on) | serpentinite → mantle | and outside the antigorite field |
mat.has_hydrous_mantle_dehydration (off) | hydrous (chlorite-bearing) mantle → mantle | , in m (Grove et al., 2009) |
mat.has_sediment_metamorphism (off) | sediment → sedimentary rock | and km |
| sedimentary rock → metasediment | or km | |
| metasediment → schist | GPa, a metapelite dehydration boundary (Wei et al., 2004) |
The antigorite field is the wedge between the lines through (730 °C, 2.1 GPa)–(500 °C, 7.5 GPa) and (730 °C, 2.1 GPa)–(650 °C, 0.2 GPa). Using one field for both serpentinite rules means no pressure and temperature satisfy both, so a marker cannot flip back and forth.
Where the mantle serpentinizes. Water released by the slab hydrates
the mantle above it. DES finds the slab with a background grid of cells of
size mesh.vt_size (in units of mesh.resolution): a cell is wet crust when
more than mat.wet_crust_fraction_threshold of its markers are oceanic
crust, sediment or sedimentary rock. A mantle marker serpentinizes when such
a cell lies below it within mat.serpentinization_thickness, optionally
only if the marker is also horizontally within the wet crust's extent plus
mat.serpentinization_wet_crust_margin.
Each active rule needs its source and target materials set
(mat.mattype_oceanic_crust, mat.mattype_eclogite,
mat.mattype_serpentinite, mat.mattype_mantle,
mat.mattype_hydrous_mantle, mat.mattype_sediment,
mat.mattype_sediment_rock, mat.mattype_metasediment,
mat.mattype_schist); DES stops at start-up if one is missing, out of
range or equal to its target. The rules and boundaries follow those of
GeoFLAC. The subduction tutorial
uses this option.
Option 1: simple subduction rules
Option 1 uses fixed material indices: 0 mantle, 1 serpentinized mantle,
2 oceanic crust, 3 eclogite, 4 sediment, 5 schist, 6 and 7 upper and lower
continental crust, and the pressure is always the lithostatic reference
pressure. Oceanic crust becomes eclogite above 500 °C and
GPa, with in kelvin; sediment becomes schist above 650 °C deeper
than 20 km; serpentinite returns to mantle above 550 °C past the
(730 °C, 2.1 GPa)–(500 °C, 7.5 GPa) line. With
control.has_hydration_processes = yes, crust and sediment hotter than
150 °C release water as separate hydrous markers, which rise at
control.hydration_migration_speed; mantle below 550 °C that holds a hydrous
marker becomes serpentinite.
References
Grove, T. L., Till, C. B., Lev, E., Chatterjee, N., & Médard, E. (2009). Kinematic variables and water transport control the formation and location of arc volcanoes. Nature, 459, 694–697.
Hacker, B. R., Abers, G. A., & Peacock, S. M. (2003). Subduction factory
- Theoretical mineralogy, densities, seismic wave speeds, and H₂O contents. Journal of Geophysical Research, 108(B1), 2029.
Ulmer, P., & Trommsdorff, V. (1995). Serpentine stability to mantle depths and subduction-related magmatism. Science, 268, 858–861.
Wei, C., Powell, R., & Clarke, G. L. (2004). Calculated phase equilibria for low- and medium-pressure metapelites in the KFMASH and KMnFMASH systems. Journal of Metamorphic Geology, 22, 495–508.